By Item #
Item # PCL9G-2032.QT
Item # PCL9G-2032.QT, Tribolube L9G, Qt. Btl
List Price $12.95
Email This Page
Save To Favorites
Tribolube-L9G meets the requirements of a SAE 75W-90 that is a oxidatively stable, corrosion resistant, wide temperature range synthetic lubricating oil. It is compatible with most plastic, elastomeric, and rubber seals, gaskets, and O-rings, except EPDM rubber.
To request the latest MSDS and TDS sheets, contact us at
or through our
Type of Lubricant
Synthetic Lubricating Oil
Specific Gravity @ 60 ºF/60 ºF
-45 to 350
Evaporation 22 hrs @ 300 ºF
Viscosity @ 100 ºF
Viscosity @ 210 ºF
Weld Load @ Load
Steel-on-Steel Wear @ 1200 rpm, 40 kg, 52100 steel, 1 hr
Rust Preventive Properties @ Procedure A
Rust Preventive Properties @ Procedure B
Oxidation Test Viscosity Incr. @ 212 ºF
Oxidation Test @ Precipitation No., Orig.
Foam Test - Sequence 1 (mls @ 5 min. air/mls settling)
Foam Test - Sequence 2 (mls @ 5 min. air/mls settling)
Foam Test - Sequence 3 (mls @ 5 min. air/mls settling)
Falex EP Test- Last Pass Load
Falex EP Test- Conversion to Contact Pressure
Timken Load Arm @ Fail Load
Timken Load Arm @ OK Load
FZG Gear Test @ Load Stage
+ 12 Stage
Load Wear Index
Last Non-Seizure @ Load/Wear Scar
Last Seizure @ Load/Wear Scar
This synthetic lubricating oil has a wide range of uses such as in gears, gear boxes, and various instruments including tachometer generator gyros, gimbals, and other applications involving light to heavy loads, small to wide amplitudes of oscillation, high rotational speeds, and where very low foaming and surface adherence is a requirement.
Function of Lubricating Greases
A good quality lubricant reduces friction and wear, dissipates heat, keeps out dirt, and prevents rust formation. It must provide good "boundary layer" lubrication, and be thin enough to get between moving parts, and once there, it must be thick enough to separate them with a slippery oil film. This oil film must be strong enough to provide full-film "hydrodynamic" lubrication between moving parts such as bearings, screw actuators, etc. It must also act as a kind of floating seal, filling in the microscopic imperfections in moving surfaces with a thin film of lubricant.
If it is too thin, under shock or extreme loads it will not separate moving surfaces. If it is too thick, it cannot squeeze between the moving parts to provide proper lubrication. If either extreme exists, friction and wear occurs; accumulating wear debris escalates wear until failure occurs.
Heat is generated between moving parts in machines, even though they are lubricated. Some greases can reduce the operating temperatures of bearings , gears, or other moving parts by having better EP and anti-wear properties thereby reducing the metal to metal contact and the associated heat. Grease lubricants also work as a seal, keeping out dirt and other foreign matter, thus preventing damage to the bearing and contact surfaces. The effect of rust or corrosion on unprotected metal can readily be understood. A lubricating film on moving parts protects them from this damage by preventing contact with air, moisture or other corrosive agents thereby increasing useful life.
Properties of Synthetic Lubricating Greases
In general, a grease is an oil that has been thickened by a solid or semisolid dispersion, commonly a clay or a soap, in a petroleum or synthetic lubricating fluid, plus the desired additives used to enhance grease performance properties.
Composition of Lubricating Greases
Petroleum or Synthetic
55% - 96%
Soap or Non-Soap
4% - 45%
0% - 20%
All of the grease components affect the physical and chemical properties. Standardized testing must be used to provide useful information about the properties of grease lubricants. Such information can then be used to compare and select a grease for a specific application. Some of these tests are described in following sections.
Purpose of Synthetic Lubricants
Demands placed upon lubricants have become increasing severe with advances in industrial machinery and equipment design. Higher operating temperatures, speeds and gear and bearing loads are stressing the capabilities of conventional petroleum-based lubricants. The OEM's have increased demands for "sealed for life" applications. Such applications require synthetic lubricants.
Synthetic lubricants were developed to meet demanding requirements which exceed the operational limits of conventional petroleum based lubricants. Because they are man-made , synthetics can be better tailored to their role as a lubricant by meeting predetermined physical and chemical properties. Formulated from pure hydrocarbons, synthetics do not contain the impure components that adversely affect the physical and chemical stability of petroleum based lubricants.
Synthetic oil and grease lubricants have been solving demanding lubrication problems by replacing petroleum lubricants in applications that exceed their environmental, operational, or service life limitations. In such applications, synthetics pay for themselves many times over in reduced component failure, repair costs, warranty costs, down time, and increased service life.
Synthetic vs Petroleum Lubricants Performance Both oil and grease lubricants made from synthetic based fluids have a much wider operating temperature range and are more thermally and oxidatively stable than lubricants made from petroleum-based fluids. Low Temperature Performance
At very low temperatures, most petroleum-based oil and grease lubricants thicken and are usually limited to temperatures no lower than -20 ºF unless high temperature performance is sacrificed. In contrast, synthetic oil and grease lubricants have good low temperature viscosity and fluidity characteristics down to as low as -140 ºF, and are still capable of operating at temperatures as high as 600 ºF.
High Temperature Performance
Lubricants are susceptible to failure at high temperature, especially in thin films after long term exposure. Recent research in boundary lubrication confirms the primary role of high temperature in lubricant degradation. Increasing temperature rather than increasing shear load has been found to induce most lubricant failures. Petroleum-based oil and grease lubricants have an upper temperature limit of about 250 ºF to 300 ºF. Above these temperatures they become fluid and volatile. If grease lubricated machinery is operated above that temperature limit, the lubricant breaks down and may melt or form hard carbon deposits. Some synthetic grease lubricants can operate up to about 600 ºF without melting.
Oxidation is the primary breakdown mode of most lubricants, leading to the formation of sludge and other corrosive compounds. When lubricants are exposed to air, oxygen, or other strong oxidizing chemicals, petroleum- based lubricants deteriorate and break down easily, especially at high temperatures. Many chemicals can attack petroleum-based lubricants resulting in gummy deposits. Lubricant failure may result in corrosion of parts, deterioration of seals, stuck or worn bearings, and product contamination. This results in frequent equipment down time for relubrication, replacement of parts, cleaning, and maintenance. The thermal and oxidative stability of synthetics often makes them the only alternative for very cold, extremely hot, sealed for life applications, or harsh operating environments.
Dust, dirt, and other debris can create additional problems for petroleum-based lubricants. These lubricants tend to attract contaminates because they are naturally occurring compounds which have unreacted molecular end groups. These end groups produce electrical charges at the surface, so when a charged dust or dirt particle comes near, they are attracted to the surface of the lubricant. The dust particles can be abrasive and damage parts and machinery. It is this characteristic of petroleum-based lubricants that create problems in dusty and dirty applications such as paper and textile mills, printing plants, and metal-forming operations. This situation leads to frequent machine down time for cleaning and relubrication. Because synthetics are man-made , they are fully reacted chemicals and do not have the unreacted end groups which attract dust and dirt. Wear of moving parts can thus be reduced in dusty environments.
Load and Wear Performance
Synthetics lubricants can provide increased wear protection over petroleum-based lubricants due to better viscosity-temperature properties. Tribolube Synthetic Lubricating Oils and Greases are specially formulated to function in applications or environmental conditions where standard "general purpose" lubricants will not perform or will perform only marginally. Tribolube lubricants outperform conventional lubricants under conditions such as hard vacuums, low and high operating temperatures, oxidizing environments, high rotating speeds, extremely high load conditions, applications where little wear can be tolerated, high radiation levels, extremely corrosive environments, and where long life is mandated.
What are the Pay Offs?
The failure of petroleum lubricants to give adequate performance is making greases and oils formulated from synthetic hydrocarbon fluids increasingly attractive. Reduced maintenance costs for manpower and replacement parts, and reduced downtime with associated production loss, make synthetic lubricants cost effective in most applications. The demand for lubricant stability over increasingly wider ranges of operating conditions exceeding the capability of petroleum lubricants is making synthetics mandatory in many OEM applications. The failure of petroleum lubricants to give adequate performance is making greases and oils formulated from synthetic hydrocarbon fluids increasingly attractive. Reduced maintenance costs for manpower and replacement parts, and reduced downtime with associated production loss, make synthetic lubricants cost effective in most applications. The demand for lubricant stability over increasingly wider ranges of operating conditions exceeding the capability of petroleum lubricants is making synthetics mandatory in many OEM applications.
Tribolube L-Series Synthetic Industrial Lubricating Oils provide the following benefits and advantages compared to conventional oils:
The excellent fluidity of low viscosity oils provides improved lubrication by ensuring better oil coverage of wear points and surfaces.
Extremely high load carrying capacity permits increased gear teeth and bearing design loads
Using lower viscosity oils permits operation at lower temperatures and increases gearbox efficiency thereby reducing energy consumption.
Wider operating temperature range eliminates the need to use separate summer and winter oils.
Technical Data Sheets
Request for Quote
Aerospace Lubricants, Inc. Site by
BusinessOL.com: A Search Engine and Internet Marketing Company